A wireless sensor so small clinicians can implant it in the blood vessels of the brain could help evaluate healing of aneurysms.
Aneurysms are bulges that can cause death or serious injury if they burst. The stretchable sensor, which operates without batteries, would wrap around stents or diverters implanted to control blood flow in vessels that aneurysms affect.
To reduce costs and accelerate manufacturing, researchers use aerosol jet 3D printing to create conductive silver traces on elastomeric substrates. The 3D additive manufacturing technique allows production of very small electronic features in a single step, without using traditional multi-step lithography processes in a cleanroom.
Researchers believe the device is the first demonstration of aerosol jet 3D printing to produce an implantable, stretchable sensing system for wireless monitoring.
“The beauty of our sensor is that it can be seamlessly integrated onto existing medical stents or flow diverters that clinicians are already using to treat aneurysms,” says Woon-Hong Yeo, an assistant professor in the School of Mechanical Engineering and the biomedical engineering department at Georgia Tech and Emory University.
“We could use it to measure an incoming blood flow to the aneurysm sac to determine how well the aneurysm is healing, and to alert doctors if blood flow changes.”
Monitoring an aneurysm from inside the brain
Inserted using a catheter system, the sensor would use inductive coupling of signals to allow wireless detection of biomimetic cerebral aneurysm hemodynamics.
Monitoring the progress of cerebral aneurysms now requires repeated angiogram imaging using contrast materials that can have harmful side effects. Because of the cost and potential negative effects, clinicians must limit their use. However, a sensor placed in a blood vessel could allow more frequent evaluations without the use of imaging dyes.
“For patients who have had a procedure done, we would be able to tell if the aneurysm is occluding as it should without using any imaging tools,” Yeo says. “We will be able to accurately measure blood flow to detect changes as small as 0.05 meters per second.”
Researchers made the six-layer sensor from biocompatible polyimide, two separate layers of a mesh pattern produced from silver nanoparticles, a dielectric and soft polymer-encapsulating material. The sensor would wrap around the stent or flow diverter, which must be less than two or three millimeters in diameter to fit into the blood vessels.
High volume, low cost
The sensor includes a coil to pick up electromagnetic energy transmitted from another coil located outside the body. Blood flowing through the implanted sensor changes its capacitance, which alters the signals passing through the sensor on their way to a third coil located outside the body.
In the laboratory, Yeo and his collaborators measured capacitance changes six centimeters (less than 2.5 inches) away from a sensor implanted in meat to simulate brain tissue.
“The flow rate is correlated really well with the capacitance change that we can measure,” Yeo says. “We have made the sensor very thin and deformable so it can respond to small changes in blood flow.”
Use of the aerosol jet 3D printing technique was essential to producing the stretchable and flexible electronics necessary for the sensor. The technique uses a spray of aerosol particles to create patterns, allowing narrower feature sizes than conventional inkjet printing.
“We can control the printing speed, the printing width, and the amount of material being jetted,” Yeo says. “The parameters can be optimized for each material, and we can use materials that have a broad range of viscosities.”
Because researchers can fabricate the sensor in a single step without costly cleanroom facilities, they could manufacture it in higher volume at lower cost.
The next phase of the aneurysm sensor will be able to measure blood pressure in the vessel along with the flow rates. “We will be able to measure how pressure contributes to flow change,” Yeo says. “That would allow the device to be used for other applications, such as intracranial pressure measurements.”
Yeo’s research team previously developed a flexible and wearable health monitor able to provide ECG and other information. He says the success of the monitoring technique demonstrates the potential for smart and connected wireless soft electronics based on nanomaterials, stretchable mechanics, and machine learning algorithms.
“We are excited that people are now recognizing the potential of this technology,” he says. “There are a lot of opportunities to integrate this sensing mechanism into ultrathin membranes that are implantable within the body.”
The research appears in Advanced Science.
The Korea Institute of Industrial Technology, and a seed grant from the Georgia Tech Institute for Electronics and Nanotechnology funded the work.
Source: Georgia Tech